rtsmart-boot-log.txt

>>> sending reboot
reboot
U-Boot SPL 2022.10 (Feb 10 2026 - 09:22:02 +0000)
00000000: PMU Major Msg: End of CA training                                            
00000000: PMU Major Msg: End of initialization                                         
00000000: PMU Major Msg: End of read enable training                                   
00000000: PMU Major Msg: End of fine write leveling                                    
00000000: PMU Major Msg: End of read dq deskew training                                
00000000: PMU Major Msg: End of MPR read delay center optimization                     
00000000: PMU Major Msg: End of Write leveling coarse delay                            
00000000: PMU Major Msg: End of write delay center optimization                        
00000000: PMU Major Msg: End of read delay center optimization                         
00000000: PMU Major Msg: End of max read latency training                              
00000000: PMU Major Msg: Firmware run has completed                                    
image: uboot load to 20000000 compress =1 src 2aaaacff len=49446 


U-Boot 2022.10 (Feb 10 2026 - 09:22:02 +0000)

CPU:   rv64imafdcvsu
Model: kendryte k230 canmv v3.0
DRAM:  1 GiB
Core:  26 devices, 13 uclasses, devicetree: embed
MMC:   mmc0@91580000: 0, mmc1@91581000: 1
Loading Environment from MMC... OK
In:    serial@91400000
Out:   serial@91400000
Err:   serial@91400000
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
image: rtt load to 0 compress =1 src 2aaaad07 len=18b75d 
Jump to big hart

OpenSBI v0.9
heap: [0x00514a80 - 0x04514a80], size 65536 KB
page: [0x04514a88 - 0x1fffec00], size 453544 KB
lwIP-2.1.2 initialized!
canaan lora0 driver register OK
ov5647 read chip id high ,ret:1
ov5647 read chip id low ,ret:1
ov5647 read chip id failed, 0x0000
Can't find sensor on csi0
[I/SDIO] SD card capacity 62586880 KB.
ov5647 read chip id high ,ret:1
ov5647 read chip id low ,ret:1
ov5647 read chip id failed, 0x0000
Can't find sensor on csi1
found partfind sensor(gc2093_csi2) on csi2
vicap_mcm_init[nit␀093_csi2) on csi2
␀ze: 30.0MB
found part[1], begin: 83886080, size: 500.0MB
found part[2], begin: 1073741824, size: 58.704GB
[I/sal.skt] Socket Abstraction Layer initialize success.
msh />Interface Descriptor:

	bLength: 0x09            

	bDescriptorType: 0x04    

	bInterfaceNumber: 0x00   

	bAlternateSetting: 0x00  

	bNumEndpoints: 0x03      

	bInterfaceClass: 0xff    

	bInterfaceSubClass: 0xff 

	bInterfaceProtocol: 0x00 

	iInterface: 0x00         

[I/WLAN.dev] wlan init success
[I/WLAN.lwip] eth device init ok name:w0
[I/WLAN.dev] wlan init success
[I/WLAN.lwip] eth device init ok name:w1
hello world ,lvgl version:8.4.1
rm69a10_power_on 
rm69a10_power_reset 
rm69a10 rst_gpio is 22 
rm69a10_power_reset 
rm69a10 rst_gpio is 22 
rm69a10_power_reset 
rm69a10 rst_gpio is 22 
rm69a10_set_backlight 
rm69a10_init 
rm69a10_set_phy_freq 
rm69a10_dsi_resolution_init 
rm69a10_568x1232_init 
rm69a10_vo_resolution_init 
vb block size is 2ac600 
vo_config_manage,virt_addr is 0x100001000 
phys_addr is 28494000 
disp_init,pic_addr is 0x100001000 
pool_id:2
tca8418_write_reg 0x23,ret:0
tca8418_read_reg 0x01 ret=-1
keyboard is not exist
user_gui_init
[INFO] [esp_brookesia_core.cpp:204](beginCore): Library version: 0.4.1
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
-----0x0414
bq27220_write_cmd_params,ret=0
-----0x3672
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
-----reset
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
-----start full access
bq27220_write_cmd_params,ret=0
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
-----start cfg_update
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
bq27220_write_cmd_params,ret=0
bq27220_write_cmd_params,ret=0
check_sum_fcc:201
bq27220_write_cmd_params,ret=0
bq27220_write_cmd_params,ret=0
bq27220_write_cmd_params,ret=0
check_sum_dc:45
bq27220_write_cmd_params,ret=0
-----exit cfg_update
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
-----exit seal
bq27220_write_cmd_params,ret=0
-----get operation status
bq27220 operation status:00 00,flag_seal:0,init_comp:0,cfg_update:0
++++++++++++++++++++++++++++++++++++++++++++++++
user_gui_init after